Design of reinforced concrete components is subtopic H of Structural Engineering on the FE Civil exam, and the beam questions follow the ACI 318 strength method: the depth of the stress block, the nominal moment, the strength reduction factor that goes with it, and the shear carried by the concrete and the stirrups.
The five problems below, in US units, follow that sequence: the stress block factor beta-1, the nominal moment of a singly reinforced beam, phi in the transition zone, the design shear strength of the concrete, and the shear left for the stirrups.
Where this sits: NCEES lists Structural Engineering at 10-15 questions of the 110 on the FE Civil exam, and design of reinforced concrete components (e.g., codes and design philosophies, beams, columns) is subtopic H of the area. NCEES does not publish question counts below that level.
The ACI Relationships These Problems Use
The FE Reference Handbook summarizes these from ACI 318; \( f'_c \) and \( f_y \) in psi or ksi, dimensions in inches.
- Stress block depth: \( a = \dfrac{A_s f_y}{0.85\,f'_c\,b} \), and \( c = a/\beta_1 \)
- Nominal moment: \( M_n = A_s f_y\,(d - a/2) \)
- \( \beta_1 \): 0.85 up to \( f'_c = 4{,}000 \) psi, 0.05 less for each 1,000 psi above that, never below 0.65
- Strength reduction, flexure (Grade 60, tied): \( \phi = 0.90 \) when \( \varepsilon_t \ge 0.005 \); in the transition zone \( \phi = 0.48 + 83\,\varepsilon_t \)
- Shear: \( V_c = 2\sqrt{f'_c}\,b_w d \) for normal-weight concrete (psi), and \( \phi V_s = V_u - \phi V_c \) with \( \phi = 0.75 \)
5 Free Reinforced Concrete Beam Problems
Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.
Problem 1 — Stress Block Factor Beta-1
A reinforced concrete beam has \( f'_c = 4{,}000\,\mathrm{psi} \). What is \( \beta_1 \)?
Answer: A) 0.85
Step 1 – Find the row in the table:
Page 280 gives \( \beta_1 \) in three ranges. For \( 2{,}500 \le f'_c \le 4{,}000\,\text{psi} \), the first row applies.
Step 2 – Read the value:
\( \beta_1 = 0.85 \).
Step 3 – Answer:
\( \beta_1 = 0.85 \). At exactly \( 4{,}000\,\text{psi} \) the first row still applies, because its limit is inclusive.
(B) \( 0.8 \) and (C) \( 0.75 \) are values the sloping middle row produces at \( 5{,}000 \) and \( 6{,}000\,\text{psi} \), and (D) \( 0.65 \) is the floor reached at \( 8{,}000\,\text{psi} \) and above.
What \( \beta_1 \) does is turn the real curved compression stress block into an equivalent rectangle of depth \( a = \beta_1 c \), and it shrinks as the concrete gets stronger because a stronger concrete is more brittle and its stress block is less full.
Correct answer: (A)
Problem 2 — Phi in the Transition Zone
A concrete section has tensile strain \( \varepsilon_t = 0.003 \). For a transition section, use \( \phi = 0.48 + 83\varepsilon_t \). What is \( \phi \)?
Answer: C) 0.73
Step 1 – Place the strain:
\( \varepsilon_t = 0.003 \) falls between \( 0.002 \) and \( 0.005 \), so the section is in the TRANSITION range and \( \phi \) is interpolated rather than read off.
Step 2 – Apply the transition expression (FE Handbook, p. 281):
\( \phi = 0.48 + 83\varepsilon_t \) for members with tied reinforcement.
Step 3 – Solve:
$$\phi = 0.48 + 83(0.003) = 0.48 + 0.249 = 0.729$$
Step 4 – Answer:
\( \phi \approx 0.73 \), which sits between the \( 0.65 \) of a compression-controlled section and the \( 0.9 \) of a tension-controlled one, exactly as a transition value should.
(D) \( 0.85 \) is not a concrete resistance factor at all; the only values on p. 281 are \( 0.9 \), \( 0.75 \) and \( 0.65 \).
(A) \( 0.56 \) and (B) \( 0.63 \) follow from no route.
Check the expression at its endpoints and it becomes hard to misremember: at \( \varepsilon_t = 0.002 \) it gives \( 0.646 \) and at \( 0.005 \) it gives \( 0.895 \), so the line simply joins the two fixed values.
Correct answer: (C)
Problem 3 — Shear Left for the Stirrups
A simply supported RC beam has \( V_u = 70\,\mathrm{kips} \). Given \( \phi = 0.75 \) and \( \phi V_c = 30\,\mathrm{kips} \). What shear must be carried by stirrups, \( \phi V_s \) (\( \mathrm{kips} \))?
Answer: B) 40
Step 1 – Write the requirement:
\( \phi V_n \ge V_u \) with \( V_n = V_c + V_s \), so \( \phi V_c + \phi V_s \ge V_u \).
Step 2 – Solve for the stirrup contribution:
$$\phi V_s = V_u - \phi V_c = 70 - 30 = 40\,\text{kips}$$
Step 3 – Answer:
\( \phi V_s = 40\,\text{kips} \), which is what the stirrups must be designed to carry.
(A) \( 30 \) is \( \phi V_c \) handed back, the part the CONCRETE carries.
(C) \( 52.5 \) multiplies \( V_u \) by \( \phi \) instead of subtracting, and (D) \( 70 \) is the whole factored shear, as though the concrete contributed nothing.
To turn this into a spacing, divide out the factor first: \( V_s = \phi V_s/\phi = 40/0.75 = 53.3\,\text{kips} \), then \( s = A_vf_yd/V_s \) from p. 282, and finally check the answer against the maximum permitted spacing, which is \( d/2 \) or \( 24\,\text{in} \) and often governs.
Correct answer: (B)
Problem 4 — Nominal Moment of a Singly Reinforced Beam
A singly reinforced rectangular beam has \( b = 12\,\mathrm{in} \), \( d = 20\,\mathrm{in} \), \( f'_c = 4{,}000\,\mathrm{psi} \), \( f_y = 60\,\mathrm{ksi} \), and \( A_s = 2.00\,\mathrm{in}^{2} \). Compute nominal moment \( M_n \) (\( \mathrm{kip{-}ft} \)) using \( M_n = A_s f_y (d - a/2) \).
Answer: D) 185
Step 1 – Get the stress block first:
$$a = \dfrac{A_sf_y}{0.85f'_cb} = \dfrac{2.00(60)}{0.85(4)(12)} = \dfrac{120}{40.8} = 2.94\,\text{in}$$
Step 2 – Nominal moment (FE Handbook, p. 281):
\( M_n = A_sf_y\left(d - \dfrac{a}{2}\right) \). The bracket is the LEVER ARM between the tension in the steel and the compression resultant, which sits at the mid-depth of the stress block.
Step 3 – Solve:
\( M_n = 2.00(60)\left(20 - \dfrac{2.94}{2}\right) = 120(18.53) = 2{,}224\,\text{kip-in} \)
\( M_n = 2{,}224/12 = 185\,\text{kip-ft} \)
Step 4 – Answer:
\( M_n \approx 185\,\text{kip-ft} \), which is the NOMINAL moment; the design moment would be \( \phi M_n \).
(C) \( 165 \) is \( 0.9M_n \), that is the design moment where the question asked for the nominal one, and (B) \( 140 \) is \( 0.75M_n \), using the SHEAR resistance factor instead of the flexural one.
(A) \( 110 \) follows from no route.
The same answer comes out of the concrete side, \( M_n = 0.85f'_cab(d - a/2) = 0.85(4)(2.94)(12)(18.53) = 2{,}223\,\text{kip-in} \), because the two internal forces are equal by construction. Getting different numbers from the two routes means the stress block is wrong.
Correct answer: (D)
Problem 5 — Design Shear Strength of the Concrete
A simply supported RC beam has factored shear \( V_u = 55\,\mathrm{kips} \). Given \( b = 12\,\mathrm{in} \), \( d = 20\,\mathrm{in} \), \( f'_c = 4{,}000\,\mathrm{psi} \), and \( \phi = 0.75 \) for shear. Compute \( \phi V_c \) where \( V_c = 2\sqrt{f'_c} \, b \, d \) (\( \mathrm{lb} \)).
Answer: A) \( 23\,\mathrm{kips} \)
Step 1 – Identify given information:
\( b_w = 12\,\text{in} \), \( d = 20\,\text{in} \), \( f'_c = 4{,}000\,\text{psi} \), normal weight concrete so \( \lambda = 1.0 \), and \( \phi = 0.75 \) for shear.
Step 2 – Concrete shear strength (FE Handbook, p. 282):
\( V_c = 2\lambda\sqrt{f'_c}\,b_wd \). Watch the units: \( \sqrt{f'_c} \) is taken in psi, so \( V_c \) comes out in POUNDS.
Step 3 – Solve:
\( \sqrt{4{,}000} = 63.2 \)
\( V_c = 2(1.0)(63.2)(12)(20) = 30{,}358\,\text{lb} = 30.4\,\text{kips} \)
\( \phi V_c = 0.75(30.4) = 22.8\,\text{kips} \)
Step 4 – Answer:
\( \phi V_c \approx 23\,\text{kips} \).
(B) \( 30 \) is \( V_c \) itself with the resistance factor never applied, which is the most common answer here.
(D) \( 45 \) is what a coefficient of \( 3 \) in place of the \( 2 \) would give, and (C) \( 36 \) follows from no route.
The comparison the question is setting up matters more than the number: \( V_u = 55\,\text{kips} \) far exceeds \( \phi V_c = 23 \), so stirrups are not optional here and must be designed to carry the difference, \( V_s = V_u/\phi - V_c = 73.3 - 30.4 = 42.9\,\text{kips} \).
Correct answer: (A)
Three Mistakes That Cost Points
- Putting f'c in ksi under the square root. In \( V_c = 2\sqrt{f'_c}\,b_w d \) the 2 assumes psi: \( \sqrt{4{,}000} = 63.2 \), not \( \sqrt{4} = 2 \). The result comes out in pounds; divide by 1,000 for kips.
- Forgetting to turn kip-in into kip-ft. \( A_s f_y (d - a/2) \) with inches gives kip-in. Divide by 12 before you compare it with options in kip-ft.
- Applying phi twice, or not at all. \( \phi V_c \) and \( \phi V_s \) are already design values: subtracting \( \phi V_c \) from \( V_u \) leaves the \( \phi V_s \) the stirrups must supply. Dividing by \( \phi \) again gives \( V_s \), a different quantity.
Frequently Asked Questions
What is beta-1 used for?
It relates the depth of the equivalent rectangular stress block to the neutral axis depth, a = beta-1 c. It is 0.85 up to 4,000 psi and drops for stronger concrete, whose real stress distribution is less rectangular.
When is a beam tension-controlled?
When the net tensile strain in the extreme layer of steel is at least 0.005 at nominal strength. Then phi is 0.90; below that the section is in the transition zone and phi falls toward 0.65 for tied members.
Is the nominal moment the design strength?
No. The design strength is phi times Mn. Mn comes from the materials and the geometry; multiply it by phi, 0.90 for a tension-controlled beam, before comparing with the factored moment Mu.
Keep Going
Practice the rest of the area on the FE Civil structural engineering practice problems page, or keep going with the beam deflection problems and column buckling problems. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.