Deflection of statically determinate beams is subtopic B of Structural Engineering on the FE Civil exam, and most items come from a handful of standard cases: a cantilever with an end load or a uniform load, and a simply supported beam with a center load or a uniform load.
The five problems below use those cases, three with numbers and two that ask how the deflection changes when the span or the moment of inertia changes. The numerical ones are in SI units, so keep E in pascals and I in meters to the fourth power until the last step.
Where this sits: NCEES lists Structural Engineering at 10-15 questions of the 110 on the FE Civil exam, and deflection of statically determinant beams, trusses, and frames is subtopic B of the area. NCEES does not publish question counts below that level.
The Beam Cases These Problems Use
The FE Reference Handbook tabulates deflections for standard beams; these four cases cover the problems on this page, with E the modulus of elasticity and I the moment of inertia.
- Cantilever, end load P: \( \delta_{max} = \dfrac{PL^3}{3EI} \)
- Cantilever, uniform load w: \( \delta_{max} = \dfrac{wL^4}{8EI} \)
- Simply supported, center load P: \( \delta_{max} = \dfrac{PL^3}{48EI} \)
- Simply supported, uniform load w: \( \delta_{max} = \dfrac{5wL^4}{384EI} \)
- Scaling: deflection grows with \( L^3 \) under point loads and with \( L^4 \) under uniform loads, and falls in proportion to \( EI \)
5 Free Beam Deflection Problems
Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.
Problem 1 — Effect of Halving I
A cantilever beam (\( L = 3\,\mathrm{m} \)) carries full-span UDL \( w \). If the moment of inertia \( I \) is reduced by \( 50\% \) (\( I \to 0.5I \)), the tip deflection becomes:
Answer: D) \( 2 \times \)
Step 1 – Identify given information: Cantilever beam with UDL. \(I\) is reduced by 50% (\(I \to 0.5I\)).
Step 2 – Proportionality: The tip deflection is \(\delta = wL^4/(8EI)\), so:
$$\delta \propto \dfrac{1}{I}$$
Step 3 – Apply the change: If \(I\) is halved:
$$\delta_{\text{new}} = \dfrac{wL^4}{8E(0.5I)} = \dfrac{2wL^4}{8EI} = 2\delta_{\text{old}}$$
The deflection doubles.
Step 4 – Answer: The deflection becomes \(2\times\) the original, matching option (D). Reducing the moment of inertia makes the beam less stiff, increasing deflection. Option (A) \(0.5\times\) would imply deflection decreased, which contradicts a weaker section.
Option (C) captures the student who treats a 50% loss of moment of inertia as a 50% gain in deflection, adding the percentage instead of taking its reciprocal.
Correct answer: (D)
Problem 2 — Center Load on a Simple Beam
A simply supported beam (\( L = 5\,\mathrm{m} \)) carries a point load \( P = 10\,\mathrm{kN} \) at midspan. \( E = 210\,\mathrm{GPa} \), \( I = 4.0 \times 10^{-5}\,\mathrm{m}^{4} \). What is \( \delta_{\mathrm{max}} \) (\( \mathrm{mm} \))?
Answer: A) 3.1
Step 1 – Identify given information:
| Span | \(L = 5\,\text{m}\) |
| Load | \(P = 10\,\text{kN}\) at midspan |
| \(E\) | \(210\,\text{GPa}\) |
| \(I\) | \(4.0 \times 10^{-5}\,\text{m}^4\) |
Step 2 – Deflection formula: \(\delta_{\max} = \dfrac{PL^3}{48EI}\)
Step 3 – Substitute and solve:
$$\delta = \dfrac{10{,}000 \times (5)^3}{48 \times 210 \times 10^9 \times 4.0 \times 10^{-5}} = \dfrac{10{,}000 \times 125}{403{,}200{,}000} = \dfrac{1{,}250{,}000}{403{,}200{,}000} = 3.1 \times 10^{-3}\,\text{m}$$
$$= 3.1\,\text{mm}$$
Step 4 – Answer: \(\delta_{\max} = 3.1\,\text{mm}\), matching option (A).
Option (C) is what you get by grabbing the uniform-load deflection formula \(5wL^{4}/384EI\) from the handbook table and plugging the 10 kN concentrated load in as \(w\), which inflates the answer by a factor of 3.125.
Correct answer: (A)
Problem 3 — Tip Deflection of a Cantilever
A cantilever beam (\( L = 2.0\,\mathrm{m} \)) with end load \( P = 5\,\mathrm{kN} \) has \( E = 200\,\mathrm{GPa} \) and \( I = 3.0 \times 10^{-6}\,\mathrm{m}^{4} \). What is the tip deflection (\( \mathrm{mm} \))?
Answer: D) 22.2
Step 1 – Identify given information:
| Length | \(L = 2.0\,\text{m}\) |
| Load | \(P = 5\,\text{kN}\) at free end |
| \(E\) | \(200\,\text{GPa}\) |
| \(I\) | \(3.0 \times 10^{-6}\,\text{m}^4\) |
Step 2 – Cantilever tip deflection formula: From the FE Handbook:
$$\delta_{\text{tip}} = \dfrac{PL^3}{3EI}$$
Step 3 – Substitute and solve:
$$\delta = \dfrac{5{,}000 \times (2.0)^3}{3 \times 200 \times 10^9 \times 3.0 \times 10^{-6}} = \dfrac{5{,}000 \times 8}{1{,}800{,}000} = \dfrac{40{,}000}{1{,}800{,}000} = 0.0222\,\text{m} = 22.2\,\text{mm}$$
Step 4 – Answer: \(\delta_{\text{tip}} = 22.2\,\text{mm}\), matching option (D). A common error is using \(EI = 200 \times 10^9 \times 1.5 \times 10^{-5}\) (wrong \(I\) value), which gives a different answer.
Option (C) is what you get by grabbing the cantilever end-slope formula \(PL^{2}/(2EI)\) from the handbook table instead of the end-deflection formula \(PL^{3}/(3EI)\), then converting the result as if it were a length.
Correct answer: (D)
Problem 4 — Effect of a Longer Span
A simply supported beam (\( L = 6\,\mathrm{m} \)) carries a central point load \( P \). If the span increases by \( 20\% \) (\( L \to 1.2L \)) with same \( P \), \( E \), \( I \), the max deflection changes by a factor of:
Answer: B) 1.728
Step 1 – Identify given information: Simply supported beam with center point load \(P\). Span increases by 20% (\(L \to 1.2L\)), with \(P\), \(E\), \(I\) unchanged.
Step 2 – Proportionality for center point load: From \(\delta = PL^3/(48EI)\):
$$\delta \propto L^3$$
Step 3 – Calculate the deflection ratio:
$$\dfrac{\delta_{\text{new}}}{\delta_{\text{old}}} = \left(\dfrac{1.2L}{L}\right)^3 = (1.2)^3 = 1.728$$
Deflection increases by a factor of \(1.728\).
Step 4 – Answer: Factor = \(1.728\), matching option (B). This shows that deflection is highly sensitive to span changes. A 20% increase in span causes a 72.8% increase in deflection due to the cubic relationship.
Option (D) is what you get by adding the original deflection back onto a ratio that already includes it - computing \(1.2^{3} = 1.728\) and then reporting \(1 + 1.728\), as if the cubic ratio were the increase rather than the factor.
Correct answer: (B)
Problem 5 — Uniformly Loaded Simple Beam
A simply supported beam of span \( L = 8\,\mathrm{m} \) carries a uniform load \( w = 6\,\mathrm{kN/m} \) over its full length. \( E = 200\,\mathrm{GPa} \) and \( I = 5.0 \times 10^{-5}\,\mathrm{m}^{4} \). What is the maximum deflection?
Answer: C) \( 32\,\mathrm{mm} \)
Step 1 – Identify given information:
| Span | \( L = 8\,\text{m} \) |
| Uniform load | \( w = 6\,\text{kN/m} \) |
| Modulus of elasticity | \( E = 200\,\text{GPa} = 200 \times 10^6\,\text{kN/m}^2 \) |
| Moment of inertia | \( I = 5.0 \times 10^{-5}\,\text{m}^4 \) |
Step 2 – Handbook equation (p. 140): For a simply supported beam with a uniform load over the whole span the table gives \( v_{\max} = -\dfrac{5wL^4}{384EI} \) at midspan. The minus sign means downward; the question asks for the size of the deflection, \( \delta_{\max} = \dfrac{5wL^4}{384EI} \).
Step 3 – Substitute and solve: Work in kN and m so the units cancel.
$$EI = (200 \times 10^6)(5.0 \times 10^{-5}) = 10{,}000\,\text{kN·m}^2$$
Then, with \( w \) in kN/m and \( L \) in m:
$$\delta_{\max} = \dfrac{5(6)(8)^4}{384(10{,}000)} = 0.032\,\text{m}$$
Step 4 – Answer: \( \delta_{\max} = 32\,\text{mm} \), matching option (C). Option (A), \( 6.4\,\text{mm} \), leaves out the factor 5. Option (B), \( 16\,\text{mm} \), uses \( 5wL^4/(768EI) \), the next row of the table, which is for a load over only half the span. Option (D), \( 51\,\text{mm} \), replaces the load by its resultant \( wL = 48\,\text{kN} \) at midspan and uses \( PL^3/(48EI) \); a load spread along the span deflects the beam less than the same total load concentrated at the center.
Correct answer: (C)
Three Mistakes That Cost Points
- Mixing kN, GPa and millimeters. Work in newtons and meters: \( 200\ \mathrm{GPa} = 200\times10^{9}\ \mathrm{Pa} \) and \( 3.0\times10^{-6}\ \mathrm{m^4} \) stays in m4. Convert the result to millimeters only at the end; a slip of 103 lands exactly on a distractor.
- Using the point-load formula for a uniform load. \( PL^3/48EI \) and \( 5wL^4/384EI \) look alike on the page. Check the load type in the figure before you substitute, and remember that w carries units of force per length.
- Scaling with the wrong power. A span 20% longer raises the deflection of a point-loaded beam by 1.2³ = 1.73, not by 1.2² = 1.44. Under a uniform load the power is four.
Frequently Asked Questions
Do I need to memorize beam deflection formulas for the FE exam?
No. The FE Reference Handbook has a table of beam deflections and slopes. Know the cases well enough to pick the right row quickly and to check that the answer comes out as a length.
Where is the maximum deflection of a simply supported beam?
At midspan when the loading is symmetric, as with a center load, a uniform load or two equal loads placed symmetrically. With an off-center point load it moves toward the load but stays close to midspan.
Why is EI called flexural rigidity?
Because deflection is inversely proportional to it: doubling E or I halves the deflection under the same load. E is a property of the material and I a property of the cross section, so a stiffer material and a deeper section do the same job.
Keep Going
Practice the rest of the area on the FE Civil structural engineering practice problems page, or keep going with the column buckling problems and reinforced concrete beam problems. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.