Shear and moment diagrams are subtopic A of Mechanics of Materials on the FE Civil exam, and they feed much of the structural work that follows. The exam rarely asks you to draw one; it asks for a reaction, the largest shear or the largest moment, which a quick sketch shows.

The five problems below, in SI units, cover a cantilever, simply supported beams with point loads, a uniform load with a center point load, and a triangular load. Three of the worked solutions include the full shear and moment diagrams.

Where this sits: NCEES lists Mechanics of Materials at 7-11 questions of the 110 on the FE Civil exam, and shear and moment diagrams is subtopic A of the area. NCEES does not publish question counts below that level.

The Beam Relationships These Problems Use

The FE Reference Handbook has a table of standard beam cases; these relationships cover the problems on this page.

5 Free Shear and Moment Diagram Problems

Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.

Problem 1 — Cantilever with a Uniform Load

A cantilever beam has length \( L = 3.0\,\mathrm{m} \) and carries a uniform load \( w = 1.2\,\mathrm{kN/m} \) over the entire span. What is the maximum bending moment at the fixed end (kN·m)?

Answer: B) 5.4

Step 1 – Identify given information:

\( L = 3.0 \;\text{m} \), \( w = 1.2 \;\text{kN/m} \), cantilever beam.

Step 2 – Maximum moment for uniform load on a cantilever (FE Handbook):

\( M_{\max} = \frac{wL^2}{2} \) (occurs at the fixed end)

Step 3 – Solve:

$$M_{\max} = \frac{1.2 \times (3.0)^2}{2} = \frac{10.8}{2} = 5.4 \;\text{kN}\cdot\text{m}$$

Step 4 – Answer: The maximum moment at the fixed end is \( 5.4 \;\text{kN}\cdot\text{m} \). Option (D) uses \( wL^2 \) (missing the \( 1/2 \) factor).

Option (C) is what you get by lumping the uniform load into a 3.6 kN resultant but placing it at two-thirds of the span - the centroid of a triangular load - instead of at midspan: \(3.6 \times 2.0 = 7.2\) kN·m.

Correct answer: (B)

Problem 2 — Two Symmetric Point Loads

A simply supported beam has span \( L = 6\,\mathrm{m} \) with two equal point loads of \( 4\,\mathrm{kN} \) located at \( x = 2\,\mathrm{m} \) and \( x = 4\,\mathrm{m} \). What is the maximum bending moment (kN·m)?

Figure for FE Civil practice problem 2 (Mechanics of Materials)

Answer: D) 8

Step 1 – Identify given information:

\( L = 6 \;\text{m} \), two equal loads of \( 4 \;\text{kN} \) at \( x = 2 \;\text{m} \) and \( x = 4 \;\text{m} \).

Step 2 – Use symmetry and statics (FE Handbook):

By symmetry: \( R_A = R_B = 4 \;\text{kN} \).

Step 3 – Solve:

Between the loads, shear is \( V = R_A - 4 = 0 \), so moment is constant there:

$$M_{\max} = R_A \times 2 = 4 \times 2 = 8 \;\text{kN}\cdot\text{m}$$

Shear (V) and bending-moment (M) diagrams
Shear force and bending moment diagrams for the beam

Step 4 – Answer: The maximum moment is \( 8 \;\text{kN}\cdot\text{m} \), constant between the two loads. This is a classic four-point bending configuration that creates pure bending.

Option (A) is what you get by using the fixed-end coefficient \(PL/8\) on a single 4 kN load, instead of summing both loads' contributions on a simply supported span.

Correct answer: (D)

Problem 3 — Uniform Load plus a Center Load

A simply supported beam has \( L = 4.0\,\mathrm{m} \) with a uniform load \( w = 3.0\,\mathrm{kN/m} \) over the span and an additional centered point load \( P = 6.0\,\mathrm{kN} \). What is the maximum bending moment (kN·m)?

Figure for FE Civil practice problem 3 (Mechanics of Materials)

Answer: C) 12

Step 1 – Identify given information:

\( L = 4.0 \;\text{m} \), \( w = 3.0 \;\text{kN/m} \) (full span), \( P = 6.0 \;\text{kN} \) at center.

Step 2 – Use superposition for maximum moment (FE Handbook):

\( M_{\text{total}} = \frac{wL^2}{8} + \frac{PL}{4} \) (both maxima at midspan)

Step 3 – Solve:

$$M_{\text{UDL}} = \frac{3.0 \times (4.0)^2}{8} = 6 \;\text{kN}\cdot\text{m}$$

$$M_{\text{point}} = \frac{6.0 \times 4.0}{4} = 6 \;\text{kN}\cdot\text{m}$$

$$M_{\text{total}} = 6 + 6 = 12 \;\text{kN}\cdot\text{m}$$

Shear (V) and bending-moment (M) diagrams
Shear force and bending moment diagrams for the beam

Step 4 – Answer: The maximum moment is \( 12 \;\text{kN}\cdot\text{m} \). Superposition is valid because both load cases are linear elastic and their maxima occur at the same location.

Correct answer: (C)

Problem 4 — Maximum Shear with Two Loads

A simply supported beam has span \( L = 5\,\mathrm{m} \) with point loads: \( 4\,\mathrm{kN} \) at \( x = 1\,\mathrm{m} \) from the left support and \( 6\,\mathrm{kN} \) at \( x = 4\,\mathrm{m} \). What is the maximum absolute shear force in the beam (kN)?

Figure for FE Civil practice problem 4 (Mechanics of Materials)

Answer: C) 5.6

Step 1 – Identify given information:

\( L = 5 \;\text{m} \), \( P_1 = 4 \;\text{kN} \) at \( x = 1 \;\text{m} \), \( P_2 = 6 \;\text{kN} \) at \( x = 4 \;\text{m} \).

Step 2 – Find reactions using moment equilibrium (FE Handbook):

\( \sum M_A = 0 \): \( R_B \cdot L = P_1 \cdot 1 + P_2 \cdot 4 \)

Step 3 – Solve:

$$R_B = \frac{4(1) + 6(4)}{5} = \frac{28}{5} = 5.6 \;\text{kN}$$

$$R_A = 10 - 5.6 = 4.4 \;\text{kN}$$

Shear diagram: \( V = +4.4 \) (left of 1 m), \( V = 0.4 \) (between loads), \( V = -5.6 \) (right of 4 m). Maximum \( |V| = 5.6 \;\text{kN} \).

Shear (V) and bending-moment (M) diagrams
Shear force and bending moment diagrams for the beam

Step 4 – Answer: The maximum absolute shear force is \( 5.6 \;\text{kN} \). Option (A) is the left reaction; option (D) is the total load.

Correct answer: (C)

Problem 5 — Reaction under a Triangular Load

A simply supported beam has span \( L = 6\,\mathrm{m} \) with a triangular distributed load that increases from 0 at the left support to \( 9\,\mathrm{kN/m} \) at the right support. What is the right support reaction \( R_B \) (kN)?

Figure for FE Civil practice problem 5 (Mechanics of Materials)

Answer: D) 18

Step 1 – Identify given information:

\( L = 6 \;\text{m} \), triangular load from 0 at left to \( 9 \;\text{kN/m} \) at right.

Step 2 – Resultant of triangular load (FE Handbook):

\( W = \frac{1}{2} w_{\max} L \), acting at \( \frac{2}{3}L \) from the zero end.

Step 3 – Solve:

\( W = \frac{1}{2}(9)(6) = 27 \;\text{kN} \) at \( x = \frac{2}{3}(6) = 4 \;\text{m} \) from left.

\( \sum M_A = 0 \): \( R_B(6) = 27(4) = 108 \), so \( R_B = 18 \;\text{kN} \).

Step 4 – Answer: The right reaction is \( 18 \;\text{kN} \). Since the triangular load is heavier near B, B carries more than half. \( R_A = 27 - 18 = 9 \;\text{kN} \).

Correct answer: (D)

Three Mistakes That Cost Points

Frequently Asked Questions

Do I need to draw complete diagrams on the FE exam?

Usually not. Most questions ask for a single value, a reaction, the largest shear or the largest moment, but a quick sketch of the shear diagram is the fastest way to see where the moment peaks.

Why does the moment peak where the shear is zero?

Because shear is the slope of the moment diagram. Where the slope changes sign the moment stops rising and starts falling, so that point is a maximum or a minimum.

Which sign convention should I use?

Any consistent one. A common convention takes shear as positive when it turns a beam segment clockwise and moment as positive when it bends the beam concave up, which makes the moment in a simply supported beam positive.

Keep Going

Practice the rest of the area on the FE Civil mechanics of materials practice problems page, or keep going with the mohr's circle and combined stress problems. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.