Combined stresses, principal stresses and Mohr's circle are subtopic D of Mechanics of Materials on the FE Civil exam. The questions give a plane stress state and ask for what Mohr's circle shows: the principal stresses, the maximum shear and the angle to the principal planes.

Three of the five problems below share one stress state, so you can follow it from the maximum shear to the principal stresses and their orientation. The other two cover the absolute maximum shear in three dimensions and the combined stress from an axial load and a bending moment.

Where this sits: NCEES lists Mechanics of Materials at 7-11 questions of the 110 on the FE Civil exam, and combined stresses, principal stresses, and Mohr's circle is subtopic D of the area. NCEES does not publish question counts below that level.

The Stress Relationships These Problems Use

The FE Reference Handbook gives these for plane stress, with tension positive.

5 Free Mohr's Circle and Combined Stress Problems

Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.

Problem 1 — Maximum In-Plane Shear

A plane stress state has \( \sigma_x = 80\,\mathrm{MPa} \), \( \sigma_y = -20\,\mathrm{MPa} \), and \( \tau_{xy} = 30\,\mathrm{MPa} \). What is the maximum in-plane shear stress \( \tau_{\mathrm{max}} \) (MPa)?

Answer: C) 58.3

Step 1 – Identify the given stress state:

ParameterValue
\( \sigma_x \)\( 80 \;\text{MPa} \) (tension)
\( \sigma_y \)\( -20 \;\text{MPa} \) (compression)
\( \tau_{xy} \)\( 30 \;\text{MPa} \)

Step 2 – Recall the maximum in-plane shear stress formula from the FE Handbook. This equals the radius of Mohr's circle:

$$\tau_{\max} = \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}$$

Step 3 – Compute \( \frac{\sigma_x - \sigma_y}{2} \):

$$\frac{\sigma_x - \sigma_y}{2} = \frac{80 - (-20)}{2} = \frac{100}{2} = 50 \;\text{MPa}$$

Note: Since \( \sigma_y \) is negative (compression), subtracting it adds to the difference: \( 80 - (-20) = 80 + 20 = 100 \).

Step 4 – Substitute into the formula:

$$\tau_{\max} = \sqrt{(50)^2 + (30)^2} = \sqrt{2{,}500 + 900} = \sqrt{3{,}400} = 58.3 \;\text{MPa}$$

Note: The center of Mohr's circle is at \( \sigma_{\text{avg}} = \frac{\sigma_x + \sigma_y}{2} = \frac{80 + (-20)}{2} = 30 \;\text{MPa} \), and the radius (\( \tau_{\max} \)) = 58.3 MPa.

Correct answer: (C)

Problem 2 — Principal Stresses

For \( \sigma_x = 80\,\mathrm{MPa} \), \( \sigma_y = -20\,\mathrm{MPa} \), and \( \tau_{xy} = 30\,\mathrm{MPa} \), what are the principal stresses \( (\sigma_1,\, \sigma_2) \) in MPa?

Answer: B) (88.3; −28.3)

Step 1 – Identify given information:

ParameterValue
\( \sigma_x \)\( 80 \;\text{MPa} \)
\( \sigma_y \)\( -20 \;\text{MPa} \)
\( \tau_{xy} \)\( 30 \;\text{MPa} \)

Step 2 – Principal stress formulas (FE Handbook):

The principal stresses are the center of Mohr's circle plus/minus the radius:

$$\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}$$

Step 3 – Solve:

Average stress (center of Mohr's circle):

$$\sigma_{\text{avg}} = \frac{80 + (-20)}{2} = \frac{60}{2} = 30 \;\text{MPa}$$

Radius (from MOM001):

$$R = \sqrt{\left(\frac{80-(-20)}{2}\right)^2 + 30^2} = \sqrt{50^2 + 30^2} = \sqrt{3400} = 58.3 \;\text{MPa}$$

Therefore:

$$\sigma_1 = 30 + 58.3 = 88.3 \;\text{MPa}$$

$$\sigma_2 = 30 - 58.3 = -28.3 \;\text{MPa}$$

Step 4 – Answer: The principal stresses are \( (88.3,\; -28.3) \) MPa. Option (A) incorrectly uses only half the difference; option (D) doubles the actual values. The negative sign on \( \sigma_2 \) confirms one principal plane is in compression.

Correct answer: (B)

Problem 3 — Orientation of the Principal Planes

For \( \sigma_x = 80\,\mathrm{MPa} \), \( \sigma_y = -20\,\mathrm{MPa} \), and \( \tau_{xy} = 30\,\mathrm{MPa} \), what are the orientations of the principal stress planes \( \theta_p \) (degrees) relative to the +x-axis?

Answer: A) (−74.5°; 15.5°)

Step 1 – Identify given information:

ParameterValue
\( \sigma_x \)\( 80 \;\text{MPa} \)
\( \sigma_y \)\( -20 \;\text{MPa} \)
\( \tau_{xy} \)\( 30 \;\text{MPa} \)

Step 2 – Principal angle formula (FE Handbook):

$$\tan(2\theta_p) = \frac{2\tau_{xy}}{\sigma_x - \sigma_y}$$

This gives two angles \( 90^\circ \) apart — the orientations of the two principal planes.

Step 3 – Solve:

$$\tan(2\theta_p) = \frac{2(30)}{80 - (-20)} = \frac{60}{100} = 0.6$$

$$2\theta_p = \arctan(0.6) = 30.96^\circ$$

$$\theta_p = 15.5^\circ$$

The second principal plane is \( 90^\circ \) away:

$$\theta_{p2} = 15.5^\circ - 90^\circ = -74.5^\circ$$

Step 4 – Answer: The principal planes are at \( (-74.5^\circ,\; 15.5^\circ) \). On Mohr's circle, the two principal directions are always \( 90^\circ \) apart in physical space (\( 180^\circ \) on the circle). Options (B) and (C) correspond to common errors of using incorrect tangent arguments.

Correct answer: (A)

Problem 4 — Absolute Maximum Shear in 3D

A material has principal stresses \( \sigma_1 = 120\,\mathrm{MPa} \), \( \sigma_2 = 50\,\mathrm{MPa} \), and \( \sigma_3 = -30\,\mathrm{MPa} \). What is the maximum shear stress \( \tau_{\mathrm{max}} \) in 3D (MPa)?

Answer: D) 75

Step 1 – Identify given information:

Principal StressValue
\( \sigma_1 \)\( 120 \;\text{MPa} \)
\( \sigma_2 \)\( 50 \;\text{MPa} \)
\( \sigma_3 \)\( -30 \;\text{MPa} \)

Step 2 – Maximum shear stress in 3D (FE Handbook):

$$\tau_{\max} = \frac{\sigma_{\max} - \sigma_{\min}}{2} = \frac{\sigma_1 - \sigma_3}{2}$$

Step 3 – Solve:

$$\tau_{\max} = \frac{120 - (-30)}{2} = \frac{150}{2} = 75 \;\text{MPa}$$

Step 4 – Answer: The absolute maximum shear stress is \( 75 \;\text{MPa} \). Option (A) uses \( (\sigma_1 - \sigma_2)/2 = 35 \), which is only one of the three possible shear stress values. In 3D, always use the largest and smallest principal stresses.

Dropping the compressive principal stress and taking half of the largest tensile stress alone gives 60 MPa, the classic "assume the third face is unloaded" slip on this item.

Correct answer: (D)

Problem 5 — Axial Load plus Bending

A beam section (\( b = 100\,\mathrm{mm} \), \( h = 200\,\mathrm{mm} \)) carries an axial compressive load \( P = 50\,\mathrm{kN} \) and a bending moment \( M = 6.0\,\mathrm{kN \cdot m} \) about the strong axis. What is the maximum compressive normal stress (MPa)?

Answer: D) 11.5

Step 1 – Identify given information:

\( b \times h = 100 \times 200 \;\text{mm} \), \( P = 50 \;\text{kN} \) (compression), \( M = 6.0 \;\text{kN}\cdot\text{m} \).

Step 2 – Combined axial and bending stress (FE Handbook):

\( \sigma = \frac{P}{A} + \frac{M}{S} \) (on the compression side, both stresses add)

Step 3 – Solve:

\( A = 0.10 \times 0.20 = 0.02 \;\text{m}^2 \), \( \quad \sigma_a = \frac{50{,}000}{0.02} = 2.5 \;\text{MPa} \)

\( S = \frac{0.10 \times (0.20)^2}{6} = 6.667 \times 10^{-4} \;\text{m}^3 \), \( \quad \sigma_b = \frac{6{,}000}{6.667 \times 10^{-4}} = 9.0 \;\text{MPa} \)

Max compression: \( \sigma_{\max} = 2.5 + 9.0 = 11.5 \;\text{MPa} \)

Step 4 – Answer: The maximum compressive stress is \( 11.5 \;\text{MPa} \). On the tension side, stresses partially cancel: \( 9.0 - 2.5 = 6.5 \;\text{MPa} \) (option B).

Option (A) is what you get by resisting the moment with a force couple over the full depth, taking \(S = A \cdot c = 2.00 \times 10^{-3}\,\mathrm{m}^{3}\) instead of \(bh^{2}/6 = 6.67 \times 10^{-4}\,\mathrm{m}^{3}\). That gives a bending stress of 3.0 MPa rather than 9.0 MPa.

Correct answer: (D)

Three Mistakes That Cost Points

Frequently Asked Questions

Do I need to draw Mohr's circle on the exam?

Not necessarily. The formulas give the same results, but a quick sketch helps with the signs and with which plane is which, especially for the angle.

Is the maximum shear stress always the radius of Mohr's circle?

The maximum in-plane shear is. The absolute maximum shear can be larger when the two in-plane principal stresses have the same sign, because the zero out-of-plane stress then sets the largest circle.

Which sign does compression take?

Negative, with tension positive. Keep the sign through the calculation; a compressive normal stress enters the center of the circle as a negative number, as in the shared stress state on this page.

Keep Going

Practice the rest of the area on the FE Civil mechanics of materials practice problems page, or keep going with the shear and moment diagram problems. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.