Area moments of inertia are subtopic F of Statics on the FE Civil exam, and they return in bending stress, deflection and buckling. The questions give a shape, often built from rectangles, circles and triangles, and ask for its moment of inertia about a stated axis.

The five problems below go from a single rectangle and a ring to an I-beam, a plate with a hole, and a trapezoid made of a rectangle and a triangle. One is in inches; the others use millimeters or centimeters.

Where this sits: NCEES lists Statics at 8-12 questions of the 110 on the FE Civil exam, and area moments of inertia is subtopic F of the area. NCEES does not publish question counts below that level.

The Section Properties These Problems Use

The FE Reference Handbook tabulates these for common shapes; for a composite area, add the parts and subtract the holes, each about the same axis.

5 Free Moment of Inertia Problems

Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.

Problem 1 — Ring about a Diameter

Annulus (ring) with outer radius \( R = 5\,\mathrm{in} \) and inner radius \( r = 3\,\mathrm{in} \). Find \( I_x \) about any centroidal diameter.

Figure for FE Civil practice problem 1 (Statics)

Answer: C) 427 in\(^{4}\)

Step 1 – Identify given information: Annulus (ring): outer radius \(R = 5\,\mathrm{in}\), inner radius \(r = 3\,\mathrm{in}\). Find \(I_x\) about a centroidal diameter.

Step 2 – Annulus MOI formula (FE Handbook):

$$I_x = \frac{\pi}{4}(R^4 - r^4)$$

This is the difference between the full circle and the hole.

Step 3 – Substitute and solve:

$$I_x = \frac{\pi}{4}(5^4 - 3^4) = \frac{\pi}{4}(625 - 81) = \frac{\pi}{4}(544) = \frac{1709.0}{4} \approx 427.3\,\mathrm{in}^{4}$$

Step 4 – Answer: \(I_x \approx 427\,\mathrm{in}^{4}\). Option (A) \(214\) is \(J/2\) of a different calculation; (D) \(855\) is the polar moment \(J = 2I_x\). For an annulus, the hollow center significantly reduces the MOI.

Option (B) is what you get by subtracting the hole from the area but then using the solid circle's radius of gyration \(R/2\) instead of the annulus value \(\sqrt{(R^{2}+r^{2})/4}\).

Correct answer: (C)

Problem 2 — Rectangle about Its Centroid

What is the centroidal area moment of inertia \( I_x \) (about the centroidal x-axis) of a rectangle with width \( b = 120\,\mathrm{mm} \) and height \( h = 60\,\mathrm{mm} \)?

Answer: B) \(2.16 \times 10^{6}\) mm\(^{4}\)

Step 1 – Identify given information: Rectangle with \(b = 120\,\mathrm{mm}\) (width) and \(h = 60\,\mathrm{mm}\) (height). Find \(I_x\) about the centroidal x-axis.

Step 2 – Centroidal moment of inertia (FE Handbook): For a rectangle about its centroidal axis parallel to the base:

$$I_x = \frac{bh^3}{12}$$

Step 3 – Substitute and solve:

$$I_x = \frac{120 \times (60)^3}{12} = \frac{120 \times 216{,}000}{12} = \frac{25{,}920{,}000}{12} = 2.16 \times 10^6\,\mathrm{mm}^{4}$$

Step 4 – Answer: \(I_x = 2.16 \times 10^6\,\mathrm{mm}^{4}\). Option (A) uses \(bh^3/24\); (C) uses \(bh^3/6\); (D) uses \(bh^3/3\) (about the edge, not centroid). The factor \(1/12\) applies only for centroidal axes; about the base it becomes \(1/3\).

Correct answer: (B)

Problem 3 — Trapezoid about Its Base

Composite area (draw as a trapezoid): Start with a rectangle \( 10\,\mathrm{cm} \) wide by \( 6\,\mathrm{cm} \) tall with origin at \( (0,\,0) \). Attach a right triangle on the right side such that the right angle is at \( (10,\,0) \), the triangle extends \( 4\,\mathrm{cm} \) to the right (to \( x = 14 \)) and \( 6\,\mathrm{cm} \) up (to \( y = 6 \)). Find \( I_x \) about the base x-axis (\( y = 0 \)).

Figure for FE Civil practice problem 3 (Statics)

Answer: A) 792 cm\(^{4}\)

Step 1 – Identify the two shapes:

The composite area is made of:

  • Rectangle: base \( b = 10\,\mathrm{cm} \), height \( h = 6\,\mathrm{cm} \), with its base on the x-axis.
  • Right triangle: base \( b = 4\,\mathrm{cm} \) (along x-axis from \( x = 10 \) to \( x = 14 \)), height \( h = 6\,\mathrm{cm} \), with its base also on the x-axis.

Step 2 – Use the additive property of second moments of area:

Since both shapes share the same reference axis (\( y = 0 \)), no parallel axis theorem is needed:

$$ I_x = I_{x,\text{rect}} + I_{x,\text{tri}} $$

Step 3 – Moment of inertia of the rectangle about its base:

From the FE Handbook, for a rectangle about its base:

$$ I_{x,\text{rect}} = \frac{b h^3}{3} = \frac{(10)(6)^3}{3} = \frac{10 \times 216}{3} = \frac{2160}{3} = 720\,\mathrm{cm}^{4} $$

Step 4 – Moment of inertia of the triangle about its base:

From the FE Handbook, for a triangle about its base:

$$ I_{x,\text{tri}} = \frac{b h^3}{12} = \frac{(4)(6)^3}{12} = \frac{4 \times 216}{12} = \frac{864}{12} = 72\,\mathrm{cm}^{4} $$

Step 5 – Total moment of inertia:

$$ I_x = 720 + 72 = 792\,\mathrm{cm}^{4} $$

Option (C) is what you get by measuring the rectangle across the full 14 cm bottom edge and then adding the triangle a second time, so the triangular region is counted twice.

Correct answer: (A)

Problem 4 — I-Beam about Its Weak Axis

I-beam composite area: Overall height \( 12\,\mathrm{cm} \). Top flange: \( 10\,\mathrm{cm} \) wide, \( 2\,\mathrm{cm} \) thick from \( y = 10 \) to \( 12 \). Bottom flange: \( 10\,\mathrm{cm} \) wide, \( 2\,\mathrm{cm} \) thick from \( y = 0 \) to \( 2 \). Web: \( 2\,\mathrm{cm} \) thick from \( y = 2 \) to \( 10 \), centered (\( x \) from \( 4 \) to \( 6 \)). Find \( I_y \) about the centroidal y-axis.

Figure for FE Civil practice problem 4 (Statics)

Answer: C) 339 cm\(^{4}\)

Step 1 – Identify given information:

Part\(b \times h\)Area\(\bar{x}_i\)
Top flange\(10 \times 2\)\(20\,\mathrm{cm}^{2}\)\(5\)
Web\(2 \times 8\)\(16\,\mathrm{cm}^{2}\)\(5\)
Bottom flange\(10 \times 2\)\(20\,\mathrm{cm}^{2}\)\(5\)

Symmetric about \(x = 5\), so \(\bar{x} = 5\) and no \(Ad^2\) term needed.

Step 2 – MOI about centroidal y-axis (FE Handbook):

\(I_y = \sum \frac{h_i b_i^3}{12}\) (all centroids aligned on \(x = 5\))

Step 3 – Compute:

Top flange: \(I_y = 2(10)^3/12 = 166.67\,\mathrm{cm}^{4}\)

Web: \(I_y = 8(2)^3/12 = 5.33\,\mathrm{cm}^{4}\)

Bottom flange: \(I_y = 2(10)^3/12 = 166.67\,\mathrm{cm}^{4}\)

$$I_y = 166.67 + 5.33 + 166.67 = 338.67 \approx 339\,\mathrm{cm}^{4}$$

Step 4 – Answer: \(I_y \approx 339\,\mathrm{cm}^{4}\). The wide flanges dominate the \(I_y\) contribution. Option (A) \(180\) counts only one flange; (B) \(260\) uses wrong dimensions; (D) \(520\) includes erroneous \(Ad^2\) terms.

Correct answer: (C)

Problem 5 — Plate with a Circular Hole

Composite area: Rectangle \( 10\,\mathrm{cm} \) (x) by \( 6\,\mathrm{cm} \) (y) with origin at bottom-left. A circular hole of radius \( 2\,\mathrm{cm} \) is centered at \( (x = 6\,\mathrm{cm},\, y = 3\,\mathrm{cm}) \). What is \( I_y \) about the centroidal y-axis (vertical axis through \( \bar{x} \))?

Figure for FE Civil practice problem 5 (Statics)

Answer: B) 472 cm\(^{4}\)

Step 1 – Identify given information: From STAT057: \(\bar{x} = 4.74\,\mathrm{cm}\), \(A_{\text{net}} = 47.434\,\mathrm{cm}^{2}\). Rectangle: \(I_{y,c} = 6(10)^3/12 = 500\,\mathrm{cm}^{4}\), \(x_r = 5\). Circle: \(I_{y,c} = \pi(2)^4/4 = 12.566\,\mathrm{cm}^{4}\), \(x_h = 6\).

Step 2 – Parallel-axis theorem about composite centroid (FE Handbook):

$$I_y = [I_{y,c,r} + A_r(x_r - \bar{x})^2] - [I_{y,c,h} + A_h(x_h - \bar{x})^2]$$

Step 3 – Compute:

Rectangle: \(500 + 60(5 - 4.74)^2 = 500 + 60(0.0676) = 500 + 4.06 = 504.06\)

Hole: \(12.566 + 12.566(6 - 4.74)^2 = 12.566 + 12.566(1.588) = 12.566 + 19.95 = 32.52\)

$$I_y = 504.06 - 32.52 = 471.5 \approx 472\,\mathrm{cm}^{4}$$

Step 4 – Answer: \(I_y \approx 472\,\mathrm{cm}^{4}\). The hole reduces the MOI. Option (A) \(300\) uses wrong formula; (C) \(640\) omits the hole subtraction; (D) \(810\) uses MOI about the edge.

Correct answer: (B)

Three Mistakes That Cost Points

Frequently Asked Questions

What is the difference between area and mass moment of inertia?

The area moment of inertia, in length to the fourth power, measures how a cross section resists bending. The mass moment of inertia, in mass times length squared, measures how a body resists rotation. Statics and mechanics of materials use the first; dynamics uses the second.

About which axis is the moment of inertia smallest?

Among parallel axes, the one through the centroid. Every other parallel axis adds A d squared, which is why section tables list centroidal values.

What is the radius of gyration?

The distance r for which A r squared equals I, so r is the square root of I over A. Column buckling uses it in the slenderness ratio KL/r.

Keep Going

Practice the rest of the area on the FE Civil statics practice problems page. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.