Basic hydraulics is subtopic B of Water Resources and Environmental Engineering on the FE Civil exam, and its core is the energy equation: Bernoulli with continuity, plus a head loss when friction matters. Rearranged, the same equation gives the flow through an orifice, a pitot tube and a venturi meter.
The five problems below, all in SI units, use it that way: the pressure behind a nozzle, the flow through an orifice, the velocity at a pitot tube, the discharge through a venturi meter, and the friction loss in a pipe.
Where this sits: NCEES lists Water Resources and Environmental Engineering at 10-15 questions of the 110 on the FE Civil exam, and basic hydraulics (e.g., Manning equation, Bernoulli theorem, open-channel flow) is subtopic B of the area. NCEES does not publish question counts below that level.
The Hydraulics Relationships These Problems Use
The FE Reference Handbook gives these in its fluid mechanics and hydraulics sections; for water \( \rho = 1{,}000 \) kg/m3 and \( g = 9.81 \) m/s2.
- Continuity: \( Q = A_1 v_1 = A_2 v_2 \)
- Bernoulli, no losses: \( \dfrac{p_1}{\gamma} + \dfrac{v_1^2}{2g} + z_1 = \dfrac{p_2}{\gamma} + \dfrac{v_2^2}{2g} + z_2 \)
- Orifice: \( Q = C_d A\sqrt{2gh} \)
- Pitot tube: \( v = \sqrt{2\,\Delta p/\rho} \)
- Venturi meter, no losses: \( Q = A_2\sqrt{\dfrac{2\,\Delta p/\rho}{1 - (A_2/A_1)^2}} \)
- Darcy-Weisbach: \( h_f = f\,\dfrac{L}{D}\,\dfrac{v^2}{2g} \)
5 Free Bernoulli and Pipe Flow Problems
Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.
Problem 1 — Velocity from a Pitot Tube
A pitot tube in water measures a stagnation–static pressure difference of \( 1.8\,\mathrm{kPa} \). Neglecting losses, what is the local flow velocity?
Answer: A) \( 1.9\,\mathrm{m/s} \)
Step 1 – Identify given information:
Stagnation-static pressure difference \( \Delta p = 1.8 \) kPa = 1,800 Pa. Fluid: water (\( \rho = 1{,}000 \) kg/m\(^3\)).
Step 2 – Pitot tube formula (FE Handbook):
\( \Delta p = \frac{1}{2}\rho v^2 \), so \( v = \sqrt{\frac{2\Delta p}{\rho}} \)
Step 3 – Solve:
$$v = \sqrt{\frac{2 \times 1{,}800}{1{,}000}} = \sqrt{3.6} = 1.90 \;\text{m/s}$$
Step 4 – Answer: \( v \approx 1.9 \) m/s. The pitot tube measures the difference between stagnation and static pressure, which equals the dynamic pressure \( \frac{1}{2}\rho v^2 \).
(B) \( 2.7\,\text{m/s} \) is \( \sqrt{2} \) times the answer, from cancelling the one half by doubling the measured pressure difference and then still applying the factor of two inside the root.
(C) \( 3.3\,\text{m/s} \) and (D) \( 6.0\,\text{m/s} \) follow from neither.
Correct answer: (A)
Problem 2 — Friction Loss in a Pipe
Water flows through a \( 60\,\mathrm{m} \) long, \( 0.15\,\mathrm{m} \) diameter pipe at \( v = 2.0\,\mathrm{m/s} \). Using Darcy-Weisbach with \( f = 0.02 \), what is the head loss \( h_f \)?
Answer: C) \( 1.6\,\mathrm{m} \)
Step 1 – Identify given information:
| Parameter | Value |
|---|---|
| Pipe length \( L \) | 60 m |
| Diameter \( D \) | 0.15 m |
| Velocity \( v \) | 2.0 m/s |
| Friction factor \( f \) | 0.02 |
Step 2 – Darcy-Weisbach equation (FE Handbook):
$$h_f = f \cdot \frac{L}{D} \cdot \frac{v^2}{2g}$$
Step 3 – Solve:
$$h_f = 0.02 \times \frac{60}{0.15} \times \frac{(2.0)^2}{2 \times 9.81} = 0.02 \times 400 \times \frac{4}{19.62} = 0.02 \times 400 \times 0.2039 = 1.63 \;\text{m}$$
Step 4 – Answer: \( h_f \approx 1.6 \) m. The Darcy-Weisbach equation is the fundamental friction loss equation. The friction factor \( f \) depends on Reynolds number and pipe roughness (Moody diagram).
(A) \( 0.5\,\text{m} \) puts the US customary \( g = 32.2\,\text{ft/s}^2 \) into an otherwise all-SI calculation, shrinking the velocity head by a factor of about \( 3.3 \).
(B) \( 0.8\,\text{m} \) halves the answer and (D) \( 3.3\,\text{m} \) doubles it.
Correct answer: (C)
Problem 3 — Pressure Behind a Nozzle
Water flows in a horizontal pipe from \( D_1 = 0.20\,\mathrm{m} \) at section 1 to \( D_2 = 0.10\,\mathrm{m} \) at section 2. At section 1, \( v_1 = 1.5\,\mathrm{m/s} \). At section 2, water discharges to atmosphere (\( p_2 = 0 \) gage). Neglect losses. What is \( p_1 \) (gage)?
Answer: D) \( 16.9\,\mathrm{kPa} \)
Step 1 – Identify given information:
| Parameter | Value |
|---|---|
| \( D_1 \) | 0.20 m |
| \( D_2 \) | 0.10 m |
| \( v_1 \) | 1.5 m/s |
| \( p_2 \) | 0 (gage) |
Step 2 – Continuity and Bernoulli (FE Handbook):
Continuity: \( v_2 = v_1 (D_1/D_2)^2 \). Bernoulli (horizontal, no losses): \( p_1 + \frac{1}{2}\rho v_1^2 = p_2 + \frac{1}{2}\rho v_2^2 \).
Step 3 – Solve:
$$v_2 = 1.5 \times \left(\frac{0.20}{0.10}\right)^2 = 1.5 \times 4 = 6.0 \;\text{m/s}$$
$$p_1 = \frac{1}{2}\rho(v_2^2 - v_1^2) = \frac{1}{2}(1000)(36 - 2.25) = \frac{1}{2}(1000)(33.75) = 16{,}875 \;\text{Pa}$$
Step 4 – Answer: \( p_1 \approx 16.9 \) kPa. The pressure at section 1 must be higher to accelerate the flow through the constriction (Bernoulli effect).
(A) \( 3.4\,\text{kPa} \) scales the velocity by the diameter RATIO instead of its square in continuity, taking \( v_2 = 3.0 \) m/s rather than \( 6.0 \), which underestimates the pressure difference by a factor of five.
(B) \( 4.2\,\text{kPa} \) and (C) \( 8.0\,\text{kPa} \) follow from neither route.
Correct answer: (D)
Problem 4 — Discharge Through an Orifice
A sharp-edged orifice of diameter \( 40\,\mathrm{mm} \) discharges water from a large tank under head \( h = 3.0\,\mathrm{m} \). Assume \( C_d = 0.62 \). What is the discharge \( Q \)?
Answer: D) \( 0.0060\,\mathrm{m}^3/\mathrm{s} \)
Step 1 – Identify given information:
Orifice diameter \( d = 40 \) mm = 0.04 m, head \( h = 3.0 \) m, \( C_d = 0.62 \).
Step 2 – Orifice discharge formula (FE Handbook):
$$Q = C_d \cdot A \cdot \sqrt{2gh}$$
Step 3 – Solve:
$$A = \frac{\pi (0.04)^2}{4} = 0.001257 \;\text{m}^2$$
$$\sqrt{2gh} = \sqrt{2(9.81)(3.0)} = \sqrt{58.86} = 7.672 \;\text{m/s}$$
$$Q = 0.62 \times 0.001257 \times 7.672 = 0.00598 \;\text{m}^3\text{/s} \approx 0.0060$$
Step 4 – Answer: \( Q \approx 0.0060 \) m\(^3\)/s. For sharp-edged orifices, \( C_d \approx 0.62 \) is the standard value used unless otherwise specified.
(C) \( 0.0042\,\text{m}^3/\text{s} \) uses \( \sqrt{gh} \) in place of Torricelli's \( \sqrt{2gh} \), losing the factor of two under the root.
(B) \( 0.0030\,\text{m}^3/\text{s} \) is half the answer and (A) \( 0.0011\,\text{m}^3/\text{s} \) is close to the orifice AREA, which is not a discharge.
Correct answer: (D)
Problem 5 — Venturi Meter Discharge
A venturi meter is installed in a horizontal water pipe. \( D_1 = 0.30\,\mathrm{m} \), \( D_2 = 0.15\,\mathrm{m} \). The pressure difference between upstream and throat is \( \Delta p = 15\,\mathrm{kPa} \) (upstream higher). Neglect losses. What is the flow rate \( Q \)?
Answer: C) \( 0.10\,\mathrm{m}^3/\mathrm{s} \)
Step 1 – Identify given information:
\( D_1 = 0.30 \) m, \( D_2 = 0.15 \) m, \( \Delta p = 15 \) kPa = 15,000 Pa (upstream higher), no losses.
Step 2 – Continuity and Bernoulli (FE Handbook):
Compute areas: \( A_1 = \frac{\pi(0.30)^2}{4} = 0.07069 \) m\(^2\), \( A_2 = \frac{\pi(0.15)^2}{4} = 0.01767 \) m\(^2\).
From continuity: \( v_2 = \frac{A_1}{A_2} v_1 = 4 v_1 \).
Step 3 – Solve for velocity and flow rate:
Bernoulli (horizontal): \( \Delta p = \frac{1}{2}\rho(v_2^2 - v_1^2) = \frac{1}{2}\rho(16v_1^2 - v_1^2) = \frac{15}{2}\rho v_1^2 \)
\( v_1 = \sqrt{\frac{2 \Delta p}{15 \rho}} = \sqrt{\frac{2(15{,}000)}{15(1{,}000)}} = \sqrt{2.0} = 1.414 \) m/s
\( Q = A_1 v_1 = 0.07069 \times 1.414 = 0.100 \) m\(^3\)/s
Step 4 – Answer: \( Q \approx 0.10 \) m\(^3\)/s. Venturi meters use the pressure difference between the upstream and throat sections to measure flow rate without moving parts.
(B) \( 0.07\,\text{m}^3/\text{s} \) drops the factor of two from the Bernoulli velocity term, using \( \sqrt{gh} \) in place of \( \sqrt{2gh} \), which shrinks the flow by \( 1/\sqrt{2} \).
(A) \( 0.05\,\text{m}^3/\text{s} \) halves the answer and (D) \( 0.20\,\text{m}^3/\text{s} \) doubles it.
Correct answer: (C)
Three Mistakes That Cost Points
- Using diameter ratios where areas belong. Continuity scales velocity with area, so halving the diameter multiplies the velocity by four, not by two.
- Leaving out the orifice coefficient. A sharp-edged orifice passes only about 60% of the ideal flow. Without the discharge coefficient the answer is the ideal discharge, about 60% too high.
- Forgetting the approach velocity in a venturi. The throat velocity comes from the pressure drop and the area ratio together. Dropping the \( 1 - (A_2/A_1)^2 \) term treats the upstream water as still and understates the discharge.
Frequently Asked Questions
What is the difference between a pitot tube and a venturi meter?
A pitot tube measures the local velocity at its tip from the difference between stagnation and static pressure. A venturi meter measures the discharge of the whole pipe from the pressure drop between the pipe and a narrower throat.
When can I neglect head losses?
When the problem says so, or the flow path is short and smooth, as in nozzles, orifices and meters. Long pipes need a friction loss from Darcy-Weisbach or Hazen-Williams.
Is the pressure in Bernoulli gage or absolute?
Either, as long as both sides use the same one. Gage pressure is usually simpler, since a jet open to the air then has a pressure of zero.
Keep Going
Practice the rest of the area on the FE Civil water resources and environmental engineering practice problems page, or keep going with the hydrology and runoff problems. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.