Fluid statics is subtopic C of Fluid Mechanics on the FE Civil exam. Pressure grows linearly with depth, and nearly every question applies that one fact to a manometer, a submerged gate or a floating body.

The five problems below, in SI units, cover a differential manometer, the force on a vertical gate that reaches the surface, the force on a circular gate, the center of pressure on a submerged gate, and the density of a floating block.

Where this sits: NCEES lists Fluid Mechanics at 6-9 questions of the 110 on the FE Civil exam, and fluid statics is subtopic C of the area. NCEES does not publish question counts below that level.

The Fluid Statics Relationships These Problems Use

The FE Reference Handbook gives these; \( \gamma = \rho g \), with \( \rho = 1{,}000 \) kg/m3 for water.

5 Free Hydrostatic Force and Fluid Statics Problems

Give yourself about three minutes for each one, roughly the pace of the exam, and work it on paper before you look at the solution.

Problem 1 — Differential Manometer

A mercury differential manometer is connected across two taps in a horizontal water line. If the pressure difference is \( 5.0\,\mathrm{kPa} \), what mercury level difference \( h \) is required?

Figure for FE Civil practice problem 1 (Fluid Mechanics)

Answer: A) 4.1 cm

Step 1 – Identify given information:
\( \Delta p = 5.0 \text{ kPa} = 5{,}000 \text{ Pa} \), mercury differential manometer in a water line.

Step 2 – Mercury column height from pressure: From the FE Handbook, for a differential manometer:

$$h = \frac{\Delta p}{(\rho_{\text{Hg}} - \rho_w)g}$$

Step 3 – Substitute and solve:

$$h = \frac{5{,}000}{(13{,}600 - 1{,}000)(9.81)} = \frac{5{,}000}{12{,}600 \times 9.81} = \frac{5{,}000}{123{,}606} = 0.0405 \text{ m} = 4.05 \text{ cm}$$

Step 4 – Answer: The correct answer is (A) 4.1 cm. The differential manometer uses the density difference \( (\rho_{\text{Hg}} - \rho_w) \) because the manometer fluid displaces the process fluid (water) in the U-tube.

Option (C) is what you get by applying the manometer balance to the travel of a single mercury leg and then doubling it, double-counting a deflection that the density-difference form already accounts for.

Problem 2 — Gate Reaching the Surface

A \( 2.0\,\mathrm{m} \) wide vertical gate is rectangular (height \( 1.6\,\mathrm{m} \)). Its top edge is at the free surface of water. What is the total force on the gate?

Figure for FE Civil practice problem 2 (Fluid Mechanics)

Answer: B) 25.1 kN

Step 1 – Identify given information:
Gate width \( = 2.0 \text{ m} \), gate height \( = 1.6 \text{ m} \), top edge at the free surface.

Step 2 – Hydrostatic force on vertical rectangular gate: From the FE Handbook:

$$F = \rho g A \bar{h}$$

Step 3 – Substitute and solve:

Area: \( A = 2.0 \times 1.6 = 3.2 \text{ m}^2 \)

Centroid depth (top at surface): \( \bar{h} = 1.6/2 = 0.8 \text{ m} \)

$$F = 1000 \times 9.81 \times 3.2 \times 0.8 = 25{,}114 \text{ N} = 25.1 \text{ kN}$$

Step 4 – Answer: The correct answer is (B) 25.1 kN. For a gate with its top edge at the free surface, the centroid is at half the gate height. The force acts at the center of pressure, which is below the centroid.

Problem 3 — Circular Gate

A vertical circular gate (diameter \( 1.0\,\mathrm{m} \)) has its center \( 3.0\,\mathrm{m} \) below the free surface. What is the resultant hydrostatic force on the gate?

Figure for FE Civil practice problem 3 (Fluid Mechanics)

Answer: C) 23.1 kN

Step 1 – Identify given information:
Vertical circular gate, diameter \( d = 1.0 \text{ m} \), centroid depth \( \bar{h} = 3.0 \text{ m} \).

Step 2 – Hydrostatic force on submerged surface: From the FE Handbook:

$$F = \rho g A \bar{h}$$

Step 3 – Substitute and solve:

$$A = \frac{\pi(0.5)^2}{1} = \pi(0.25) = 0.785 \text{ m}^2$$

$$F = 1000 \times 9.81 \times 0.785 \times 3.0 = 23{,}103 \text{ N} = 23.1 \text{ kN}$$

Step 4 – Answer: The correct answer is (C) 23.1 kN. The force depends on the area and the depth of the centroid, not the center of pressure.

Option (B) is what you get by taking the head to the top edge of the gate, 2.5 m, rather than to its centroid at 3.0 m, in the same γ h̄ A formula.

Problem 4 — Density of a Floating Block

A cube (side \( 0.40\,\mathrm{m} \)) floats in oil (\( SG = 0.80 \)) with \( 0.10\,\mathrm{m} \) of its height above the oil surface. What is the cube's density?

Answer: A) 600 kg/m\(^{3}\)

Step 1 – Identify given information:

Cube side length \(s = 0.40\,\mathrm{m}\), freeboard (height above oil) \(= 0.10\,\mathrm{m}\), and oil \(SG = 0.80\).

Step 2 – Find the submerged depth and fraction:

The depth below the oil surface is the side length minus the freeboard:

$$d = 0.40 - 0.10 = 0.30\,\mathrm{m}$$

Because the cube has a uniform horizontal cross-section, the submerged volume fraction equals the submerged depth fraction:

$$\dfrac{V_{\text{sub}}}{V_{\text{total}}} = \dfrac{d}{s} = \dfrac{0.30}{0.40} = 0.75$$

Step 3 – Find the oil density:

$$\rho_{\text{oil}} = SG \times \rho_{\text{water}} = 0.80 \times 1000 = 800\;\mathrm{kg/m}^{3}$$

Step 4 – Apply floating equilibrium (\(F_B = W\)):

For a freely floating body the buoyant force equals the weight, so \(\rho_{\text{oil}}\, g\, V_{\text{sub}} = \rho_{\text{cube}}\, g\, V_{\text{total}}\). Solving for the cube density:

$$\rho_{\text{cube}} = \rho_{\text{oil}} \times \dfrac{V_{\text{sub}}}{V_{\text{total}}} = 800 \times 0.75 = 600\;\mathrm{kg/m}^{3}$$

A value of \(800\;\mathrm{kg/m}^{3}\) (option B) would equal the oil density, meaning the cube is neutrally buoyant and fully submerged — that contradicts the stated \(0.10\,\mathrm{m}\) of freeboard, since a floating body must be less dense than the fluid.

Flipping the floating-equilibrium ratio - dividing by the submerged fraction instead of multiplying by it - inflates the cube density from 600 to about 1100 kg/m^3, which the candidate rounds to the offered value.

Correct answer: (A)

Problem 5 — Center of Pressure on a Submerged Gate

A rectangular gate \( 1.2\,\mathrm{m} \) wide and \( 2.0\,\mathrm{m} \) tall is vertical in water. The top edge is \( 0.5\,\mathrm{m} \) below the surface. Where is the center of pressure measured below the surface?

Figure for FE Civil practice problem 5 (Fluid Mechanics)

Answer: C) 1.72 m

Step 1 – Identify given information:

ParameterValue
Gate width \( b \)\( 1.2 \text{ m} \)
Gate height \( h \)\( 2.0 \text{ m} \)
Top edge depth\( 0.5 \text{ m} \)

Step 2 – Center of pressure formula: From the FE Handbook:

$$y_{cp} = \bar{h} + \frac{I_g}{A\bar{h}}$$

Step 3 – Substitute and solve:

Centroid depth: \( \bar{h} = 0.5 + 2.0/2 = 1.5 \text{ m} \)

Second moment of area: \( I_g = \frac{bh^3}{12} = \frac{1.2(2)^3}{12} = 0.8 \text{ m}^4 \)

Area: \( A = 1.2 \times 2 = 2.4 \text{ m}^2 \)

$$y_{cp} = 1.5 + \frac{0.8}{2.4 \times 1.5} = 1.5 + 0.222 = 1.72 \text{ m}$$

This matches option (C) 1.72 m.

Step 4 – Answer: The correct answer is (C) 1.72 m. The center of pressure is always below the centroid for a submerged surface. The offset \( I_g/(A\bar{h}) \) decreases as the surface is placed deeper.

Three Mistakes That Cost Points

Frequently Asked Questions

Are the pressures in these problems gage or absolute?

Gage, unless the problem says otherwise. Atmospheric pressure acts on both sides of a gate or a manometer and cancels out.

Why does the force on a submerged gate depend only on its centroid's depth?

Because pressure grows linearly with depth, the average pressure over a plane surface equals the pressure at its centroid. The shape of the surface changes where the force acts, not how large it is.

How do I find the density of a floating object?

Set its weight equal to the weight of the liquid it displaces. The fraction of its volume below the surface equals the ratio of its density to the liquid's density.

Keep Going

Practice the rest of the area on the FE Civil fluid mechanics practice problems page. To see these topics mixed with the other 13 areas, take the free FE Civil practice exam, or browse every topic in the free FE Civil practice problems hub.